We’ll investigate the VICTONY AC1200 Extender Setup from every angle in this piece. The Victony dual-band AC1200 wireless extender, which has four external antennas and offers excellent Wi-Fi range at home or at work, will be the first thing we look at.
You can begin internet browsing right away thanks to the fast setup and installation. Because it handles IEEe802.11a/ac/n/g/b standards, the majority of expander products on the market are compatible with it. It starts quickly because it is a plug-in and enables WPS.
How do i login victony ac1200 extender via web browser?
- Start by positioning the extender in the router’s centre and in the empty area.
- Then make sure that at least 50% of the signals are being sent to the expansion device by your router.
- Put the Victony AC1200 extension in “continuous/extender mode” after turning it on.
- Hold on for a short while until the power LED turns a bright green colour.
- Next, access the Wi-Fi settings on each of your devices, including your phone, tablet, and portfolio, and link to Victony’s wifi name.
- Either Wireless-N or Victony Extender will be used.
- You will at first be perceived as an unsecured open network.
- Once you’ve completed connecting, you’ll hear the message “No internet.”
- Open the browser on your device, choose ap.setup, and then input the “admin” username and password. Everything is very small.
- Select the network you wish to extend next, give it a name, and then confirm it by entering its password.
- It will reboot for about 60 seconds after every change have been made before your PCs can be added.
- Your Wi-Fi list should display the Victony AC1200 rebroadcast network, which you should connect your devices to. (SSID EXT).
Note:- If you need any assistance regarding your victony wifi extender so contact our technician or visit the official website that is ap.setup.
How can i setup victony ac1200 wifi extender via wps method
- Opening in the same room, connect the Victony AC1200 extender setup using WPS.
- After the power LED of the AC1200 has steadied for a few seconds, press and hold the WPS button for two seconds.
- A good setup is shown by the LED lights on both devices starting to blink, which should happen after 10-15 seconds.
- The Victony wa1200 would therefore have complete green WPS LEDs.
- If this doesn’t work, keep in mind to restart the extender and attempt again.
- The extension can then be removed and put somewhere within the router’s coverage, for example.
- The SSID EXT List will contain the passcode you use for your Wi-Fi extender.
Victony AC1200 extender as an Access Point
Without an issue, access point mode is quicker than range extender mode. You should install an Ethernet wire in your walls or use one that is 20 to 30 feet long. Make sure the devices are turned on and in access point mode before we begin.
- Set up wa1200 as the main entry point.
- First, connect your AC1200 to the place where you intend to use it.
- From the LAN port on your repeater, connect an Ethernet wire to the LAN extender port.
- In the event that you connect your Victony Extender to your phone, laptop, or tablet, your identity will appear in the Wi-Fi list.
- Launch a browser on the connected devices, and then type 192.168.10.1 into the address window.
- This launches the Victony AC1200 extension’s setup screen. Now the login page is being pointed to. Enter “admin” as the login and the corresponding password. Everything is very small.
- After entering the credentials, choose the “entry point” from the setup wizard, and then select Next.
- The SSID, verification, and password of a new access point will now be requested.
- It then restarts, allowing you to join your devices to the newly created network.
How do I update the Victony AC1200 firmware?
Follow these instructions to update the firmware on your Victony AC1200 Extender:
- Fire up your computer browser.
- The URL to enter is wifi.wavlink.com.
- Type in the traditional passcode.
- Press Login.
- Then, upload the most current Victony AC1200 firmware.
- When the configuration is complete, tap the setup button.
- The firmware upgrade causes a reboot of your extender.
- The Victony AC1200 firmware upgrade is now complete.
To prevent problems, keep your router plugged into a reliable power source while the upgrade is running. Furthermore, be aware that any custom router setups you have made may be lost if the firmware is updated.
